问题描述：
英语翻译
NOTES :UNLESS OTHERWISE SPECIFIED .
1.MATERIAL :ANTISTATIC MATERIAL IS NOT NECESSARY.
OPAQUE ABS FOR OPTICAL MICE.
DETAIL PLEASE REFER TO DWS-762884-0000 (SPEC-HW,PERMISSIBLE MATERIAL ADDENDUM).
HAZARDOUS SUBSTANCE MANAGEMENT :Cd LESS 5ppm ,FOLLOW LOGITECH ENCIRONMENTAL.
REQUIREMENTS,HAZARDOUS SUBSTANCE,STD-750779-0000 FOR OTHER SUBSTANCE.
2.DRAFT ANGLES TO BE 1%%176FOR UNTEXTURED SURFACES AND 2.5%%176FOR TEXTURED SURFACES.
3.ALL UNSPECIFIED EXTERIOR (APPEARANCE SURFACE) EDGES TO BE 0.13 MAXIMUM RADIUS,EXCEPT AT PARTING LINE.
4.ALL UNSPECIFIED EXTERIOR (NON-APPEARANCE SURFACE) EDGES TO BE 0.13 MAXIMUM RADIUS,EXCEPT AT PARTING LINE.
5.STRSIGHT EDGES TO HAVE A STRAIGHTNESS TOLERANCE OF 0.05 PER 25.0,NOT TO EXCEED 0.10 OVER THE ENTIRE LENGTH.
6.SCULPED SURFACES PEFER TO 3D FILE PROVIDED BY LOGITECH.
7.ONE HALF OF A FEATURE DIMENSION ACROSS A CENTER LINE AND/OR A SYMETRICAL
CALL-OUT IS EQUAL TO THE DIMENSION SHOWN DIVIDED BY 2 AND ITS TOLERANCE DIVIDED BY 2.
8.GATE TRIM TO BE 0.5 MAXIMUM,IF NO FUNCTIONAL IMPACT IN ASSEMBLY.
9.NO SINK OR DEPRESSIONS TO BE VISIBLE ON APPEARANCE SURFACES.
10.APPEARANCE SURFACES TO BE FREE OF COSMETIC DEFECTS INCLUDING,BUT NOT LIMITED TO SPLAY,PARTICLES,BURNED PLASTIC/MARKS,AND SIMILAR IMPERFECTIONS.PART MUST MEET THE REQUIREMENTS OF LOGITECH QUALITY SPECIFICATION GOI-740885-00.
NOTES :UNLESS OTHERWISE SPECIFIED .
1.MATERIAL :ANTISTATIC MATERIAL IS NOT NECESSARY.
OPAQUE ABS FOR OPTICAL MICE.
DETAIL PLEASE REFER TO DWS-762884-0000 (SPEC-HW,PERMISSIBLE MATERIAL ADDENDUM).
HAZARDOUS SUBSTANCE MANAGEMENT :Cd LESS 5ppm ,FOLLOW LOGITECH ENCIRONMENTAL.
REQUIREMENTS,HAZARDOUS SUBSTANCE,STD-750779-0000 FOR OTHER SUBSTANCE.
2.DRAFT ANGLES TO BE 1%%176FOR UNTEXTURED SURFACES AND 2.5%%176FOR TEXTURED SURFACES.
3.ALL UNSPECIFIED EXTERIOR (APPEARANCE SURFACE) EDGES TO BE 0.13 MAXIMUM RADIUS,EXCEPT AT PARTING LINE.
4.ALL UNSPECIFIED EXTERIOR (NON-APPEARANCE SURFACE) EDGES TO BE 0.13 MAXIMUM RADIUS,EXCEPT AT PARTING LINE.
5.STRSIGHT EDGES TO HAVE A STRAIGHTNESS TOLERANCE OF 0.05 PER 25.0,NOT TO EXCEED 0.10 OVER THE ENTIRE LENGTH.
6.SCULPED SURFACES PEFER TO 3D FILE PROVIDED BY LOGITECH.
7.ONE HALF OF A FEATURE DIMENSION ACROSS A CENTER LINE AND/OR A SYMETRICAL
CALL-OUT IS EQUAL TO THE DIMENSION SHOWN DIVIDED BY 2 AND ITS TOLERANCE DIVIDED BY 2.
8.GATE TRIM TO BE 0.5 MAXIMUM,IF NO FUNCTIONAL IMPACT IN ASSEMBLY.
9.NO SINK OR DEPRESSIONS TO BE VISIBLE ON APPEARANCE SURFACES.
10.APPEARANCE SURFACES TO BE FREE OF COSMETIC DEFECTS INCLUDING,BUT NOT LIMITED TO SPLAY,PARTICLES,BURNED PLASTIC/MARKS,AND SIMILAR IMPERFECTIONS.PART MUST MEET THE REQUIREMENTS OF LOGITECH QUALITY SPECIFICATION GOI-740885-00.
问题解答：
我来补答展开全文阅读